How does a car Air Conditioner work?


Air conditioning works continuously and has refrigerant continually circulating around a sealed system. Most automotive A/C systems are made up of six main components:-

  1. Compressor and mounting brackets
  2. Condenser
  3. Receiver / drier
  4. Expansion Valve
  5. Evaporator
  6. Hose & fittings
The easiest way to explain how the system works is to trace the refrigerant as it flows through the system:-



A/C systems are split into two sides, the low pressure side and the high pressure side. The two points that separate the sides are the compressor’s reed valves and the expansion valve at the evaporator. If we start at the compressor this is a pump and like most pumps it has a pressure side and a suction side. The suction side of the A/C system pulls refrigerant in gas form, refrigerant that has stored enormous amounts of latent heat. The refrigerant exits the compressor at high pressure and proceeds to the condenser. Oil that lubricates the compressor is carried in suspension with the refrigerant and circulates through the system.

The condenser is really just a big heat exchanger a devise mounted in the air stream usually in front of vehicles radiator. It can transfer heat stored in the refrigerant to the air moving over the coils and fins. The combination of high pressure and heat loss that occurs in the condenser means the refrigerant is converted from a gas to a more than 90% liquid / gas mix when the system is working properly.

This mix of mostly liquid refrigerant leaves the condenser and pours into the receiver / drier. The receiver / drier is a metal canister with five functions:-
  1. Separate the refrigerant liquid from a mix of vapor and liquid.
  2. Filter the refrigerant for residual solids.
  3. Filter the refrigerant for acids
  4. Remove moisture from the system.
  5. Store the reserve liquid refrigerant for surge conditions.


As the refrigerant pours into the receiver / drier, the liquid goes to the bottom of the canister and the gas rises to the top. Refrigerant leaving the receiver / drier must move out through a tube that extends almost to the bottom of the canister. In a properly charged system this assures that only liquid refrigerant will leave the receiver / drier.

Refrigerant must be kept extremely clean and dry so most receiver / driers contain both a filter and a desiccant to absorb impurities and moisture as the refrigerant flows through the system.
When the refrigerant leaves the receiver / drier it has been pressurised by the compressor, cooled and converted into mostly liquid by the condenser and separated into pure liquid refrigerant by the receiver / drier. This high pressure liquid refrigerant moves next to the expansion valve.

The expansion valve is one of the two separators between high pressure and low pressure in the A/C system. Though different types of valve may be used, you can think of the expansion valve as a very small orifice with high pressure on one side and low pressure, liquid droplets rapidly changing to a gas on the downstream side.

The expansion valve is located on the inlet side of the evaporator. As the high pressure liquid refrigerant moves through the expansion valve, the pressure drops and the refrigerant moving into the evaporator starts to vaporize. When a material changes from a liquid to a gas, a tremendous amount of heat is absorbed.

The evaporator is another small heat exchanger and looks like a small radiator. The refrigerant moves through the tubes while an electric fan moves cabin air across the multiple fins that surround the tubes. As the refrigerant, now at low pressure, moves through the tubes, warm air is constantly moving over the fins causing the refrigerant to continue vaporizing and to continue absorbing heat from the ambient air.

Because cool air carries less moisture than hot air, the evaporator functions as a dehumidifier as well. Moisture that collects on the fins of the evaporator is collected in a tray in the bottom of the evaporator housing and runs through a tube and exits the car.

Most expansion valves have a capillary tube that runs from the valve to the outlet of the evaporator. As the temperature at the outlet of the evaporator becomes cooler or warmer, this refrigerant charged capillary tube, working through a diaphragm attached to the valve itself, can open or close the valve to control the temperature.

Low pressure refrigerant leaving the evaporator travels to the suctions side of the compressor completing the cycle and to start the process again.

9 comments:

  1. Thanks for sharing, this is a fantastic information.Much thanks again. Fantastic.
    Cisco Training

    ReplyDelete
  2. It is best to set home air conditioners at a set temperature this will keep the comfort level of a house consistent throughout the day and night. You do not want to constant change the temperature or turn the unit on and off, this can cause a huge change in your electric bill.

    Air Conditioning - Austin Air Conditioning

    ReplyDelete
  3. I really like your blog. I really appreciate the good quality content you are posting here for free. Flipkart Coupon

    ReplyDelete
  4. why am I getting water in the bottom of the furnace when using the furnace for heating only,
    have no humidifier, where is the water coming from?

    ReplyDelete
  5. why am I getting water in the bottom of the furnace when using the furnace for heating only,
    have no humidifier, where is the water coming from?

    ReplyDelete
  6. Mention the yr using your key words as on-line customers are fired up to have recent data. This can be a smart way of having website commenting. Your blogging site or blogs should really glance desirable, eye-catching and then the title need to be unique to ensure that viewers can�t resist reading it. NayaShopi

    ReplyDelete
  7. Last month, when i visited your blog i got an error on the mysql server of yours..-~�~ look what i found

    ReplyDelete